FIBRE OPTIX SERIES 3 DUAL (DIVERSITY) CHANNEL
OPTIX2-S3-US
SPECIAL ORDER
Out of stock, please contact JPRO for delivery ETA
1 Year WARRANTY
RF Over Fibre Remote Antenna Distribution System for Wireless Microphones
OPTIX Series 3 is a high-performance RF to fibre optic (RFoF) conversion system designed to facilitate the remote placement of wireless audio antennas. The OPTIX ...
OPTIX Series 3 is a high-performance RF to fibre optic (RFoF) conversion system designed to facilitate the remote placement of wireless audio antennas. The OPTIX ...
RF Over Fibre Remote Antenna Distribution System for Wireless Microphones
OPTIX Series 3 is a high-performance RF to fibre optic (RFoF) conversion system designed to facilitate the remote placement of wireless audio antennas. The OPTIX Transmitter module converts RF signals arriving from an antenna source into a single mode optical signal, sending that signal down a length of fibre-optic cable to the OPTIX Receiver module which converts the source signal back into RF.
Without any signal loss over the optical cable, the OPTIX system can extend the range of antenna placement up to several kilometres, eliminating the need for bulky and lossy coaxial cable runs. Well-suited for live production as well as installed sound, OPTIX Series 3 features extensive user configurable controls to manage signal level, apply DC power for active antennas or amplifiers, and even directly monitor outputs to dial in performance. Compatible across VHF, UHF, and the 900 MHz band, OPTIX Series 3 is compatible across any brand wireless audio system.
The OPTIX Series 3 is available in a single or diversity (dual) channel configurations.
What are the factory settings for the Optix Series 3?
- On the TX units the DC Control is preset to (0) and the Gain Adjust is preset to (A).
- On the RX units the Gain Mode is preset to (1) and the Output level is preset to (2).
PRODUCT COMBINATIONS
The OPTIX Series 3 can be used with both wireless microphone and IEM systems. If using with IEMs the input power must be padded. Maximum RF input power is 0dBm/1mW. Do not exceed. Do not connect Optix modules to IEMs, IFBs, intercoms, or other transmit devices without attenuating input. Exceeding input voids warranty.
OPTIX Series 3 is a high-performance RF to fibre optic (RFoF) conversion system designed to facilitate the remote placement of wireless audio antennas. The OPTIX Transmitter module converts RF signals arriving from an antenna source into a single mode optical signal, sending that signal down a length of fibre-optic cable to the OPTIX Receiver module which converts the source signal back into RF.
Without any signal loss over the optical cable, the OPTIX system can extend the range of antenna placement up to several kilometres, eliminating the need for bulky and lossy coaxial cable runs. Well-suited for live production as well as installed sound, OPTIX Series 3 features extensive user configurable controls to manage signal level, apply DC power for active antennas or amplifiers, and even directly monitor outputs to dial in performance. Compatible across VHF, UHF, and the 900 MHz band, OPTIX Series 3 is compatible across any brand wireless audio system.
The OPTIX Series 3 is available in a single or diversity (dual) channel configurations.
FREQUENTLY ASKED QUESTIONS
What are the factory settings for the Optix Series 3?
- On the TX units the DC Control is preset to (0) and the Gain Adjust is preset to (A).
- On the RX units the Gain Mode is preset to (1) and the Output level is preset to (2).
PRODUCT COMBINATIONS
The OPTIX Series 3 can be used with both wireless microphone and IEM systems. If using with IEMs the input power must be padded. Maximum RF input power is 0dBm/1mW. Do not exceed. Do not connect Optix modules to IEMs, IFBs, intercoms, or other transmit devices without attenuating input. Exceeding input voids warranty.
